Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
They are making a number of good points relating to Installing A Bathtub as a whole in this content in the next paragraphs.
Setting up a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard job. If the old bathtub is easily obtainable, the task can move quickly; if you need to open a wall surface to remove the old bathtub as well as place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have certified yourself for the task and are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to take into consideration using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This post will certainly assist you install a brand-new bath tub in your restroom if you have currently bought a brand-new bathtub and do not require to change the plan of your previous water pipes.
Your devices and also material checklist ought to consist of the following:
Planning for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the restricted access that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the required placement. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water supply as well as examine all joints and new pipework for leakages and also tighten them if essential. Fill the tub as well as also inspect the overflow outlet and the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been used at least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap as well as the sink. Secure the tap in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The previous type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in complications with dampness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break rather very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub? Place feedback directly below. We'd be glad to listen to your opinions about this review. We are looking forward that you come back again before long. You should set aside a second to share this blog posting if you appreciated it. Thanks for your time invested reading it.
This Website
Report this page